WR-AOTS™ Ver. 2.08 Manual
Taining field design

Edit window

Please push Edit button to open the Edit window.

The Edit window is to create and draft a temporal draft training field. The training field itself is not changed as long as the drafting is not completed.

Buttons, lists and textboxes in the window are operated by the left button of pointing device such as mouse.

1. New button

   Button to create a new draft training field. Previous draft training field will be deleted.

   To the Window
2. Object list

   List of the objects consisting of the draft training field. One of the objects in the list can be selected.

   To the Window
3. Add button

   Button to add an object to the draft training field. Kind of object to be added can be selected the following Kind list.

   To the Window
4. Kind list

   List to select a kind of the object to be added.

   To the Window
5. Delete button

   Button to delete the selected object in the Object list.

   To the Window
6. Cancel button

   Button to withdraw the draft training field and quit the drafting. The training field is not changed.

   To the Window
7. OK button

   Button to overwrite the draft training field on the training field. The training field is changed as drafted.

   To the Window
8. Property list

   List to show properties of the selected object in the Object list. The properties are different depending on a kind of object.

   To the Window
9. Property value list

   List to show values of properties of the selected object in the Object list. One of the property values in the list can be selected.

   To the Window
10. Property value edit textbox

    Textbox to edit the selected property value in the Property value list.

    To the Window
11. Property value edit complete button

    Button to fix the edited content in the Property value edit textbox. If the other property value is selected without pushing this button, the results of edit in the Property value edit textbox is withdrawn.

    To the Window

Method to create

This section explains how to create a new training field. Please push the Edit button and open the Edit window first.

* When the Edit window opens, if there is unsaved training field, the question window Field data is not saved. will open. If you want to save it, please push Cancel button and save it. If you want to withdraw it without saving, please push OK button.

* If there is no objects in the Object list on the Edit window, the draft training field has no objects. If there is some objects, please push the New button to delete them.

1. Add object.

   Please select a kind of object to be added from the Kind list. There is four kinds of objects; Sound, Wall, Road and Mark.

   • Sound

     Object to generate sound. This kind of object can make various sounds. They also can move straight in constant velocity, or turn 90 deg around a certain point.

   • Wall

     Object to reflect and insulate sounds.

   • Road

     Object to be used for designing the training field. This kind of object do not influence on the sound propagation.

   • Mark

     Object to be used for designing the training field. This kind of object do not influence on the sound propagation.

   Explanation here is supposed that Sound is selected. Please push the Add button after you selected Sound in the Kind list. Some strings will appear on the empty Object list, Property list and the Property value list.

   

   Sound01 appeared in the Object list is the newly added object. The Property list shows the properties of Sound. The Property value list contains the default values of each properties.

   To top of Method to create
2. Set property value.

   Sound, Wall, Road and Mark has the following properties.

   • Sound

     • Name

       Name of this Object

     • Device, Card and Phrase

       Properties to assign a kind of Sound. Device is a serial number of the Sound, and it is assigned automatically when the Sound is added. For use of Card and Phrase, please refer to Sound data management.

     • Volume

       Volume of the the Sound in % (percent). Maximum value is 100, and Minimum value is 0. If the value is 0, sound is not emitted.

     • Position (X, Y, Z)

       (Initial) position of the Sound. To set the coordinates (X, Y, Z), please refer to Coordinates of training field.

     • Velocity (X, Y, Z)

       Velocity vector of the Sound. If it is zero vector, the Sound is still. Otherwise, the Sound moves. To set the components (X, Y, Z), please refer to Coordinates of training field.

     • Start, Stop and Repeat

       Properties concerning reproduction of the Sound. Start is always 0. Stop is duration of the Sound in s. If Repeat is on, when the Sound reproduction is finished, it will return to the starting point (its position will also return to the initial position). Otherwise, Sound will finish and disappear after reproduced once.

     • Turn, Center (X, Y, Z)

       Properties concerning turn of the Sound. If Turn is on, The Sound turns 90 deg horizontally (automatically decelerates before turning, accelerates after turning, and finally moves straight by the same speed) around Center position. If it is off, the Sound keeps moving straight without turning. To set the coordinates (X, Y, Z) of the Center, please refer to Coordinates of training field. Z is always 0.

     

   • Wall

     • Name

       Name of this Object

     • Position (X, Y)

       Center position of the Wall. To set the coordinates (X, Y), please refer to Coordinates of training field.

     • Width

       Width of the Wall in m.

     • Direction

       Direction of the Wall. Whether the facing direction of the Wall surface is south-north or east-west is assigned by S or N, W or E.

     

   • Road

     • Name

       Name of this Object

     • Position 1, 2 (X, Y)

       Positions of both endpoints of center line of the Road.To set the coordinates (X, Y), please refer to Coordinates of training field.

     • Width

       Width of the Road in m.

     

   • Mark

     • Name

       Name of this Object

     • Position (X, Y)

       Position of the Mark. To set the coordinates (X, Y), please refer to Coordinates of training field.

     

   Here, the method to set the Property Position X of the Object Sound01 is explained as an example. Please click the Property value 0.0 of the Property Position X in the Property value list. The Property value 0.0 of the Property Position X will be selected, and the Property value 0.0 will also appear in the Property value edit textbox.

   

   Let's change the value of the Property value edit textbox. Here the values is replaced with 20 as an example. Please input 20 from keyboard. The value of the Property value edit textbox will be overwritten and will change from 0.0 to 20. After this, please push the Property value edit complete button. The Property value of Position X in the Property value list will change to 20.0.

   
   To top of Method to create
3. Complete edit.

   Please push the OK button. The Edit window will close. The draft training field will be overwritten on the training field, and new creation of training field is completed.

   

   * When the OK button is pushed, if re-calibration is recommended in advance to the next run, the message window that recommends re-calibration will open. Please push OK button to close the message window. As the recommendation, please re-calibrate before the next run.

   

   Please make sure that the training field that you created is displayed on the monitor correctly. In this example, the Sound Sound01 is located at 20 m south from the origin.

   
   To top of Method to create

(Appendix) Coordinates of training field

In the coordinates of the training field, the head center position of the Trainee in the training field at the calibration is an origin, the axis toward south (upper direction on the monitor) is a X-axis, the axis toward east (left direction on the monitor) is a Y-axis, and the axis toward upper (rising direction from the monitor) is a Z-axis.

Values of X, Y and Z are expressed in m for position, and in m/s for velocity vector.

* The coordinates value Z is measured from the head height of the Trainee in the training field. Please note that Z is not a height from the ground. Z = 0 means that it is the same height as the head, and not as the ground.

* The Property that has only X and Y (cannot be set Z value) is the Property that can be set only the horizontal position of south-north and east-west (the height cannot be set).

* The scale of the grid on the training field monitor is 5 m/div

Method to edit

This section explains how to edit the existing training field. If any training field is already loaded, or any edited and created training field is there, you can open the Edit window to edit it by pushing the Edit button.

* If the training field is not saved yet, the question window Field data is not saved. will open. If you want to save it, please push Cancel button and save it. If you want to chage it without saving, please push OK button.

• Add object.

  It is basically the same as the method to add object in Method to create. You can add multiple objects in the same manner.

  To top of Method to edit
• Delete object.

  Please select the object that you want to delete from the Object list, and push the Delete button. Please be careful that the deleted object cannot be revived.

  
  To top of Method to edit
• Set property value.

  It is basically the same as the method to set property value in Method to create. Please select the object to which you want to set property value from the Object list, and set each property values in the Property value list.

  To top of Method to edit
• Complete edit.

  It is basically the same as the method to complete edit value in Method to create. If you push the OK button, the draft training field will be reflected. If you push the Cancel button, the draft training field will be withdrawn, and the training field will not be changed.

  To top of Method to edit

Method to save

If you want to save the training field data, please push the Save button on the Main window, or if the question window Field data is not saved. opens, please push the Cancel button. The Save window will open and you can save the training field data.

The training field data is XML format. Its file extension is .xml.

* The part that is obtained by excepting the extension from the training field file name that is set when it is saved will be the training field name.

Method to show source code

Please push the Source button on the Main window. The Source (source code of XML) window will open.

* The Source window is to browse the source code of XML, and is not to use for editing.

* Please refer to Advanced information for the detail of the XML.

Samples

The Lessons folder of WR-AOTS™ Ver. 2.08 contains samples of the training field data files. You can edit and use them freely.

* The Lessons folder contains English and 日本語 (Japanese) folders. Please use data in the English folder.

• Ambulance.xml
• APS-1.xml
• APS-2.xml
• APS-DA-Chirp.xml
• APS-DA-Cuckoo.xml
• APS-DA-PVS.xml
• Car and Opening.xml
• Curve.xml
• DefaultLesson.xml (the training field data file that will be loaded in default)
• EVHV10kmh.xml
• EVHV20kmh.xml
• RunningCar-1.xml
• RunningCar-4.xml
• RunningCars and Walls.xml
• School and Pedestrian.xml
• StillSound-1.xml
• SubwayEntrance.xml
• Wall-1.xml

Tips for design

• The upper limit numbers of the objects are 90 for Sound and 100 for others. The actual number of available Sound is depending on the throughput of your computer, and in some case you can not add so many Sounds because of poor throughput. You are recommended to make sure that your Sounds work well without intermit when you designed the training field.
• If you put Walls facing each other in parallel, please put them at least 4 m apart because of the limitation of reflected sound processing.
• When you set the turn of the Sound, please take care that, if the Center of the turn is located at the position where the Sound cannot turn around, the Sound will move straight without turning even if the Turn is set as on.